Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of RADILON A RV500RKC 106 NT - PA66-GF50 - RadiciGroup High Performance Polymers

Material Data Center offers the following functions for RADILON A RV500RKC 106 NT:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Radilon A datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
商品の説明文
PA66 50% glass fibre reinforced injection moulding grade. Heat stabilized. Natural colour.

Suitable for parts requiring very high stiffness and mechanical resistance. Good resistance to hydrolysis. Product specifically intended for applications in civil and industrial water management sector. Suitable and approved for drinking water and foodstuff contact.
Processing/Physical Characteristics乾燥/調湿単位テスト基準
ISO データ
成形収縮率, 平行 0.2 / * % ISO 294-4, 2577
成形収縮率, 直角 0.7 / * % ISO 294-4, 2577
機械的特性乾燥/調湿単位テスト基準
ISO データ
引張弾性率 16600 / 14300 MPa ISO 527
破壊応力 250 / 190 MPa ISO 527
破壊ひずみ 3 / 3.2 % ISO 527
シャルピー衝撃強さ, +23°C 110 / 120 kJ/m² ISO 179/1eU
ノッチ付きシャルピー衝撃強さ, +23°C 17 / 25 kJ/m² ISO 179/1eA
熱的特性乾燥/調湿単位テスト基準
ISO データ
溶融温度, 10°C/min 260 / * °C ISO 11357-1/-3
荷重たわみ温度, 1.80 MPa 250 / * °C ISO 75-1/-2
ビカット軟化温度, B 255 / * °C ISO 306
厚さhでの燃焼性 HB / * class IEC 60695-11-10
試験片の厚さ 0.8 / * mm -
Yellow Card 可用 はい / * - -
電気的特性.乾燥/調湿単位テスト基準
ISO データ
体積抵抗率 1E13 / 1E11 Ohm*m IEC 62631-3-1
表面抵抗率 * / 1E10 Ohm IEC 62631-3-2
耐トラッキング性 600 / - - IEC 60112
その他の特性.乾燥/調湿単位テスト基準
吸水率 4 / * % Sim. to ISO 62
吸湿率 1.1 / * % Sim. to ISO 62
密度 1570 / - kg/m³ ISO 1183
機能
 応力-ひずみ. , RADILON A RV500RKC 106 NT (乾燥), PA66-GF50, RadiciGroup
 応力-ひずみ. , RADILON A RV500RKC 106 NT (調湿), PA66-GF50, RadiciGroup
 割線弾性率−ひずみ. , RADILON A RV500RKC 106 NT (乾燥), PA66-GF50, RadiciGroup
 割線弾性率−ひずみ. , RADILON A RV500RKC 106 NT (調湿), PA66-GF50, RadiciGroup
特殊な特性
成形加工法.
射出成形.
納入形状.
顆粒., ナチュラルカラー
添加剤.
離型剤.
特殊な特性.
熱安定化.
耐薬品性
Hydrolytically Stable
Certifications
Food contact, Drinking water contact
領域別の利用可能性
その他の情報
村遜速揃
The material is delivered in moisture-proof packaging ready for processing. Maximum recommended water content for best processing is 0.15%. Typical conditions with a desiccant drier: temperature 80 ° C, dew point -20 ° C or below, time 2-4 h or more. Special care must be taken to avoid moisture absorption and contamination with other polymers when adding regrind material. Colour variation and mechanical properties reduction may occur and should always be carefully monitored.

Injection Molding Processing Parameters
Melt TemperatureMold TemperatureInjection Speed
280 - 300°C80 - 100°Cmedium-high
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.